Sor Direct or Remote Mount Explosion Proof UL/CSA/ATEX Instrukcja Użytkownika Pobierz pdf (Strona 1)

Form 416 (01.13) ©SOR Inc.

1/8

These instructions provide information for installation and

field calibration of B Temperature Switches.

Process temperature changes cause proportional

vapor pressure changes in the temperature sensing

bulb that acts on a diaphragm/piston assembly to

actuate and deactuate a snap-action electrical switching

element at discrete process temperatures. The instrument’s

behavior is determined by vapor pressure (105 range model

fill media is inert gas). For best results with the SOR

thermal activated temperature switch, the entire probe

must experience the media being monitored. If a

thermowell is being used, a thermal paste is recommended

to ensure the transfer of heat through the well to the probe.

B Temperature Switches

General Instructions

Registered Quality System to ISO 9001

Design and

specifications are

subject to change

without notice.

For latest revision, go to

www.sorinc.com

Table of Contents

Installation ....................................... 2

SIL Installation ..................................2

Electrical Connection ...........................3

Calibration .......................................3

Dimensions ......................................4

Operation.........................................6

ATEX Marking Information .....................7

Declaration of Conformity .....................8

and

ment’s

model

ended

probe

NOTE: If you suspect that a product is defective, contact the factory

or the SOR Representative in your area for a return authorization

number (RMA). This product should only be installed by trained

and competent personnel.

1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1 - B Temperature Switches

Form 416 (01.13) ©SOR Inc. 1/8These instructions provide information for installation and field calibration of B Temperature Switches.Process temperat

Strona 2 - Installation

2/8Form 416 (01.13) ©SOR Inc. Remote-Mount Probe — CapillarySecure a housing-mounting pad to bulkhead, panel rack or pipe stanchion with suitable 1/4”

Strona 3 - Electrical Connection

Form 416 (01.13) ©SOR Inc. 3/8CalibrationElectrical ConnectionEnsure that wiring conforms to all applicable local and national electrical codes and in

Strona 4 - B-Series

4/8Form 416 (01.13) ©SOR Inc. Dimensions 3/4” hex set point adjusting nut Calibration scale Housing mounting pad See g and for temperature sensi

Strona 5 - Contact the factory for

Form 416 (01.13) ©SOR Inc. 5/8Dimensions are for reference only.Contact the factory for certified drawings for a particular model number.Linear = mm/i

Strona 6 - Operation

6/8Form 416 (01.13) ©SOR Inc. For ATEX Certi ed ModelsMaximum Surface TemperatureT6 Rating - 85oCT5 Rating - 100oCOperationDesignatorAdjustable Range

Strona 7 - ATEX Marking Information

Form 416 (01.13) ©SOR Inc. 7/8ATEX Marking InformationFor ATEX Certi ed ModelsManufacturer’sRegistered TrademarkATEX Listing InformationThread Form I

Strona 8 - of Conformity

Komentarze do niniejszej Instrukcji

Brak uwag

Sor Direct or Remote Mount Explosion Proof UL/CSA/ATEX Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Czujniki Sor Direct or Remote Mount Explosion Proof UL/CSA/ATEX. SOR Direct or Remote Mount Explosion Proof UL/CSA/ATEX User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Sor Direct or Remote Mount Explosion Proof UL/CSA/ATEX Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Czujniki Sor Direct or Remote Mount Explosion Proof UL/CSA/ATEX. SOR Direct or Remote Mount Explosion Proof UL/CSA/ATEX User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Czujniki Sor Direct or Remote Mount Explosion Proof UL/CSA/ATEX