Sor TA Nuclear Qualified Temperature Switch Instrukcja Użytkownika Pobierz pdf

Form 655 (04.13) ©SOR Inc.

1/8

The SOR

temperature switch utilizes a SAMA Class II thermal system.

Nuclear Qualified

Temperature Switches

General Instructions

Design and

specifications are

subject to change

without notice.

For latest revision, go to

www.sorinc.com

NOTE: If you suspect that a product is defective, contact the factory or the SOR Representative

in your area for a return authorization number (RMA). This product should only be installed by

trained and competent personnel.

Table of Contents

Recommended Measurement Procedure ...1

N6 Housing ......................................3

TA Housing .......................................4

RT Housing ......................................5

Installation ....................................... 6

Site Storage .....................................6

Electrical Connection ...........................6

Calibration .......................................7

In considering the validity of a measurement,

remember that temperature-sensing devices respond

only to the temperature that they experience. It may

be considerably different from the temperature one

is attempting to measure if the sensor is of improper

size or configuration, or if the sensor is not adequately

coupled thermally to the media whose temperature is

being measured. The calibration procedures given below

will assure accurate and repeatable measurement of the

set points of SOR temperature switches. If the switch is

normally mounted in a thermowell, consideration should

be given to the effect this may have on the accuracy of

the switch. It is recommended that a heat transfer paste

or oil be used to thermally couple the sensing bulb to the

thermowell, both in service and during testing.

Recommended Measurement Procedure

ass

thermal

system.

per

ately

n below

the

itch is

should

r paste

lb to the

NOTE: This type of system requires that the entire

length of the sensing bulb be exposed to the

temperature being measured.

1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1 - Temperature Switches

Form 655 (04.13) ©SOR Inc. 1/8The SOR® temperature switch utilizes a SAMA Class II thermal system. Nuclear QualifiedTemperature Switches General Inst

2/8Form 655 (04.13) ©SOR Inc. Recommended temperature measurement procedure for switches used to sensetemperatures of liquids and steam with set point

Strona 3 - N6 Housing

Form 655 (04.13) ©SOR Inc. 3/8N6 Housing Remote MountDirect MountCover Screws1/8” NPT(F) Vent ConnectionBodyProcess ConnectionSensing Bulb3/4” NPT(

Strona 4 - TA Housing

4/8Form 655 (04.13) ©SOR Inc. TA HousingMounting Hardware Fasteners per SOR Test Report 9058-102 consist of three standard-grade 1/4-inch U bolts (not

Strona 5 - RT Housing

Form 655 (04.13) ©SOR Inc. 5/8Mounting Hardware Fasteners per SOR Test Report 9058-102 consist of two 1/4-20, Grade 5 screws (not supplied). Torque sc

Strona 6 - Installation

6/8Form 655 (04.13) ©SOR Inc. Site StorageStore switch in a dry area in the original shipping package. Shelf life is 10 years for a maximum ambient te

Strona 7 - Calibration

Form 655 (04.13) ©SOR Inc. 7/8CalibrationTo adjust temperature at which switch will operate, remove cover and tighten the hex head adjusting nut with

Strona 8 - Printed in USA www.sorinc.com

8/8Form 655 (04.13) ©SOR Inc. 14685 West 105th Street, Lenexa, KS 66215  913-888-2630  800-676-6794 USA  Fax 913-888-0767Printed in USA www.s

Komentarze do niniejszej Instrukcji

Brak uwag

Sor TA Nuclear Qualified Temperature Switch Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Czujniki Sor TA Nuclear Qualified Temperature Switch. SOR TA Nuclear Qualified Temperature Switch User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Czujniki Sor TA Nuclear Qualified Temperature Switch